Effect of carbon nanotubes addition on electrochemical performance and thermal stability of Li4Ti5O12 anode in commercial LiMn2O4/Li4Ti5O12 full-cell

Li₄Ti₅O₁₂ (LTO)/carbon nanotubes (CNTs) composite material is synthesized based on a solid-state method by sand-milling, spray-drying and calcining at 850 ℃ under N₂ flow. The LTO/CNTs samples with 1 wt% and 3 wt% weight ratio of CNTs addition and the pristine LTO sample are prepared. The rate performance and the thermal stability of these samples are investigated based on LiMn₂O₄ (LMO)/LTO full-cell. The results show that theweight ratio of CNTs addition has distinct effect on LTO performances. The composite materials of LTO composited CNTs have better performance at high-rate due to the intercalation enhancement by conductive network of CNTs. At second, the overcharging temperature response of the cell's surface with 1 wt% CNTs addition is the lowest. The particle size distribution is measured and the most uniform particles are obtained with 1 wt% CNTs addition. This trend could explain that the mediumquantity of CNTs is optimal to improve the heat and mass transfer and prevent the problems of crystallite growing interference and aggregation during the calcination process.     

On constitutive modeling of aluminum alloys for tube hydroforming applications

The increased interest in lightweight materials for automotive structures has also lead to a search for efficient forming methods that suit these materials. One attractive concept is to use hydroforming of aluminum tubes. The advantages of this forming method includes better tolerances, decreased number of parts and an increased range of forming options. By using FE simulations, the process can be optimized to reduce the risk for failure, i.e. bursting or wrinkling. However, extruded aluminum is highly anisotropic and it is crucial that the material model used for simulations is able to accurately describe this behavior. Also, tube hydroforming occurs predominantly in a biaxial stress state which should be considered in the material testing, where uniaxial tests are used extensively in the industry today. The present study accentuates the need for improved constitutive models. It is shown that a material model, which accurately describes the anisotropic behavior of aluminum tubes, can be obtained from simple and robust experiments.     

腐蚀磨损协同作用率的研究

提出了腐蚀与磨损“协同作用”的概念，并用于判断腐蚀与磨损协同作用的性质及大小和确定腐蚀磨损过程中材料损失的主要形式。介绍了协同作用率的测定方法，并以Ｇ１０５钢及化学镀Ｎｉ－Ｐ合金在５．０％ＮａＣｌ溶液中的腐蚀腐损作为研究对象，研究了载荷、滑动速度对腐蚀磨损协同作用的影响。结果表明：协同作用率随载荷增大而增大，随滑动速度增大而减小。     

Chemical synthesis and characterization of manganese oxide coated Ni particles

Nanosized Ni particles with an average diameter of about 8 nm were prepared by reducing of NiCl 2 with sodium borohydride (NaBH 4 ) in aqueous solution. By moderate annealing in protective atmosphere, the composite grew up to be 15-20 nm particles. Both of the as-prepared and annealed Ni particles were coated by a layer of manganese oxide via decomposition reaction in aqueous KMnO4 solution. Hysteresis loops of as-prepared samples show a large increase in the magnetization with decreasing temperature and an unsaturated component at high magnetic field. In contrast, the ferromagnetic characteristics of annealed one are much stronger with large magnetization and coercivity. The thermomagnetic curves verified the coexistence of ferromagnetic Ni and antiferromangetic Mn oxide phases. But there exists no exchange bias behavior in the samples, even though the interface structure between the ferromagnetic Ni core and the antiferromagnetic manganese oxides has been distinctly formed. The absence of exchange bias probably originates from the weak ferromagnetic characteristic of Ni cores.     

回转窑多粒径颗粒流动与偏析的DEM模拟与实验研究

为明晰回转窑内颗粒的运动行为及偏析机理,以绿豆、黄豆和黑豆为颗粒介质,依次对3种装填顺序下的颗粒流动过程进行离散元模拟与实验研究,以颗粒质量分数和平均粒度为判据,对颗粒偏析进行评价。结果表明,回转窑内颗粒流动区可分为自由滚落区、渗流呆滞区以及窑壁携带区,自由滚落区颗粒流速最大,而渗流呆滞区流速最小。窑内颗粒沿轴向输运过程发生径向偏析,形成夹层结构,小颗粒受渗流作用在渗流呆滞区中心形成内核,大粒径和中等粒径颗粒集中在自由滚落区和窑壁携带区。窑内颗粒力链分布不均匀,强力链分布于近窑壁区,弱力链分布于自由滚落区和渗流呆滞区,且渗流呆滞区力链细而密集。当窑头附近不同粒径颗粒存在轴向速度差时,颗粒在轴向发生掺混,并产生径向偏析。     

Investigation of the performance of bipolar transverse plate ESP in the sintering flue control

In order to improve the particle collection efficiency of the electrostatic precipitator (ESP), a transverse plate ESP with bipolar discharge electrodes is proposed. The simulations of the velocity distribution have shown that when the inlet velocity is 1 m/s, within the range of 40 mm from electrode plate, the average velocities of windward side and leeward side are less than 0.7 m/s and 0.3 m/s respectively. It is clear that the velocity near the collection electrode plate of this bipolar ESP is much lower than that of the ordinary ESP at the same inlet velocity. This low velocity can lead to higher efficiency for fine dust collection due to the less dust re-entrainment in ESP. It is also found that the average velocities are getting lower when the distance between plates electrodes are greater than 150 mm in accordance with the simulations. The voltage current characteristics of the bipolar ESP are superior to the ordinary ESP. The pressure drop of the bipolar ESP is about 30% higher than that of the ordinary one. The dust penetration of the bipolar ESP is about 54% less than that of the ordinary ESP when the sintering dust with 25.405 μm mass median diameter is used as the test particulate under the condition of the electric field from 2.1 kV/cm to 3.2 kV/cm and the velocity from 1.0 m/s to 1.5 m/s.     

Characterization of the globular oxide inclusion ratings in steel using laser-induced breakdown spectroscopy

Grade assessment of steel is generally performed via the metallographic method, which is timeconsuming and is not able to provide the elemental distribution information. In this paper, we present a method to measure the globular oxide inclusion ratings in steel using laser-induced breakdown spectroscopy (LIBS). The measurement is performed in two basic steps: steel samples are polished using metallographic sand paper and the Al₂O₃ inclusion number and size distribution in a marked area are observed using scanning electron microscope/energy dispersive X-ray spectroscopy (SEM/EDS) for further LIBS scanning analysis. The threshold intensity that distinguishes soluble aluminum and insoluble aluminum inclusions is determined using LIBS combined with the SEM/EDS statistical data. Carbon steel (the sample number is S9256) and bearing steel (the sample number is GCr15) are analyzed in scanning mode, and the number of Al₂O₃ inclusions in different size ranges is obtained from the statistical information derived from the Al₂O₃ size calibration curve. According to heavy and thin series for globular oxide inclusions grade assessment, the method we propose is comparable to the traditional metallographic method in terms of accuracy; however, the process is simplified and the measurement speed is significantly improved.     

Comparison of microstructure and mechanical properties of ultra-narrow gap laser and gas-metal-arc welded S960 high strength steel

The microstructural characteristics and mechanical properties, including micro-hardness, tensile properties, three-point bending properties and Charpy impact toughness at different test temperatures of 8 mm thick S960 high strength steel plates were investigated following their joining by multi-pass ultra-narrow gap laser welding (NGLW) and gas metal arc welding (GMAW) techniques. It was found that the microstructure in the fusion zone (FZ) for the ultra-NGLW joint was predominantly martensite mixed with some tempered martensite, while the FZ for the GMAW joint was mainly consisted of ferrite with some martensite. The strength of the ultra-NGLW specimens was comparable to that of the base material (BM), with all welded specimens failed in the BM in the tensile tests. The tensile strength of the GMAW specimens was reduced approximately by 100 MPa when compared with the base material by a broad and soft heat affected zone (HAZ) with failure located in the soft HAZ. Both the ultra-NGLW and GMAW specimens performed well in three-point bending tests. The GMAW joints exhibited better impact toughness than the ultra-NGLW joints.